Posts Tagged With: Wood

Getting Started in Woodworking

One of the absolute most common questions I get is “what tools do I need to get started in woodworking?”  In all honesty, that’s actually not a very easy question to answer, but I will give it a shot.  So here goes…

First….a few disclaimers:

  • I love power tools.  If you’re looking for hand tool recommendations, I can offer suggestions, but there are so many that it makes it difficult to narrow down the exact tool for the job.
  • I’m not sponsored by any tool manufacturers, these are just brands that I’ve had experience with.
  • These are just my recommendations and you should choose based off of your budget and need for that tool.

You have to understand that answering that question is not as simple as “get 1, 2, 3 and you’re good to go” because there are way too many factors at play in the mind of the person asking the question.  I can only answer from my own experience and perspective.  So, if you’re asking that question, I think you should also ask a couple more questions first.

  1. How much am I willing to spend to get started?
  2. What is it I actually want to make when I get started?

First the cost issue.  Your budget will dictate the priority of what you buy and where you buy it.  If your budget is low, start with searching Craigslist, eBay, and frequenting garage sales.  You’ll find plenty of tools that are still perfectly usable, but may not last as long as a new one.  Wear and tear is natural with any kind of tool, so getting them used isn’t a big deal as long as they do what they were meant to do.  If you go out and buy a ton a brand new tools without answering question #2, you may end up being the person who is turning right back around and selling them on Craigslist within a few months.

For the second question, you don’t need every tool under the sun to get started so figure out what types of things you want to make, then figure out what tools you need to make those things.  Don’t buy things you don’t need.  Trust me, buying tools is a rabbit hole that you WILL eventually tumble down.  You’ll buy things that you rarely (or never) use.  You don’t want to start that way.

With that out of the way, here’s what I think just about EVERY person needs to get started in woodworking.

A few basics that may be obvious

These are items that are somewhat obvious, but also may be things that you forget to pick up on your first trip to the store.  Now in the case of these small items, brands don’t really matter.  Think of these tools as essential, but keep you mind you will also lose them, break them, and a lot of times misplace them.


Any hammer will do for most jobs, but be aware that some have wooden, fiberglass, or steel handles and some are different weights.  Some have textured heads and some are smooth.  Mostly, you just need something to bang things together and occasionally pry things apart.

Tape Measure

Obvious maybe, but if I could make a suggestion consider getting two different lengths.  A 30′ tape is nice if you’re measuring a room, but can be bulky and overkill if you’re building a recipe box.  For smaller projects I would have a 6′ or 12′ tape handy, and multiples of those sizes if you’re prone to forgetting where you put things.

Speed Square

This is great for quickly drawing a perpendicular line on lumber, drawing or finding the angel of something, squaring up two pieces of lumber and even acting as a straight line guide for a circular saw cut.  They have plastic ones, but I’d go with metal.

Utility knife

Again, obvious maybe but definitely handy.  Great for opening packages, cutting straps but also scoring lines and trimming off splinters without getting too much tear out.  There are all sorts of different types, just be sure to grab extra blades and don’t be afraid to switch to a sharp blade often.


My weakness!  Buying clamps can get out of hand quickly because you can literally never have too many clamps.  There are lots of different types but to get started, I’d just buy a couple of spring and bar clamps.  As far as material, I recommend metal, not plastic. Harbor Freight is a great to get cheap starter clamps.

Circular Saw

A circular saw is probably one of the cheapest saws that you can buy and also one of the most versatile.  It can do most of what a table saw can do with enough patience and attention.  You’ll probably also want to get at least two clamps and a long straight edge so you can get long accurate straight cuts.

I’ve had this one for a really long time and it’s always worked well.



You certainly don’t have to get both a drill and a driver to get started, as a drill can do both jobs but once I moved over to having both, I was sold.  The driver helps in a lot of cases to not power through and force a screw in causing damage to the work piece, but it also adds the extra strength to get the screw in when it’s fighting back against you.  It’s kind of hard to explain why that’s useful without using a driver personally.  It’s also really handy to have two tools, one with a drill bit and one with a screw driver bit so that you can switch tools quickly rather than switch bits.  If you can swing it, I’d suggest getting the combo, and get at least an 18v set.  That seems, in my experience, to be the baseline power package that can get through most anything.

I’ve had this one for a really long time and it’s always worked well.


Alternatively, a corded drill is sometimes cheaper and usually runs at a much higher RPM.  I had a corded no brand drill for years and it picked up the slack where my old 12v cordless drill couldn’t keep up.

To accompany the tools, you’ll need at least a small set of drill bits and driving bits.  These sets can get pretty elaborate and often have a bunch of stuff you don’t need, so stick to the smaller kits to get started.


Orbital Sander

There are lots of different types of sanders, but I tend to think that the orbital is the most versatile.  A belt sander is handy for removing a LOT of material, but you can easily over do it if the grit is too rough.  The orbital sanders usually have variable speed, so you can lower the speed to more carefully sand in areas.  The one I have has a really wide speed range and has lasted a long time.  Make sure that you get a range of different grits so you can swap out the paper as needed.  I’d start with 80, 150, 220 grits.

I’ve had this one for a really long time and it’s always worked well.

Table Saw (not a necessity, but handy)

A table saw is seen by many new woodworkers as a necessity and while it’s really handy, it’s essentially a circular saw bolted upside down in a table.  You can, in theory, use a circular saw to do almost all that you could do with a table saw.  Having a table saw does however make a lot of cuts more precise and generally safer.  You can easily cut longer boards, and with the addition of multiple sleds you can cut more complex angles and joinery.

If you do go toward getting a table saw, there is a cost gap that you’ll see immediately and you will have to decide which side of that gap you want to be on.  As a beginner, my suggestion is to go on the lower cost side as a starting point.  What I mean by cost gap is that you’ll see contractor saws (semi portable) in a lot of different brands in the $200-$500 range.  This is usually where you’ll see brands like Dewalt, Ridgid, Ryobi, Bosch, etc.  After that there is a gap of around $1000 before the next tier starts (saws usually sitting on four legs).  In this group you’ll see brands like Grizzly, Delta, Rigid, SawStop and more.  These brands at this price range are usually getting into cabinet saws (there’s a box to the floor under the surface) that usually have beefier motors and solid table tops.

There are definite advantages to a cabinet saw, but jumping in for your first saw at that price point is NOT necessary.  In fact, once you outgrow your contractor saw, you can be the person who is selling a tool on Craigslist to a new woodworker.

Sticking to the contractor group… between those brands, honestly, I doubt there is much of a difference.  In fact, there are only three major tool manufacturers that provide tools to stores like Home Depot, so you’re often getting the EXACT same tool in a different color make up.  My suggestion is to just find what works in your budget, maybe ask around for first hand experience with brands and just get started.  They’ll all cut wood 🙂

Portable Table Saw                                                               Contractor (cabinet) Table Saw


What about all of the other tools I see people use?

Well, again my recommendation is look back to the beginning of this post.  Answer those two questions and see if you really need any of those other tools (yet).

With the three (possibly four) that I’ve listed above, you’ll be WELL on your way to building woodworking projects and you can pick up other tools as you find a specific need or project for them.

Enjoy and happy woodworking!!


Categories: Uncategorized | Tags: , , , , , , , , , | Leave a comment

Create a free website or blog at